Monday, October 19, 2015

Don't get too Lax - First true infection

I have a confession, I have gotten too lax with my brewing.  I have caught an infection in my brown ale, and I possible have another off flavor in my most recent brew, a blonde ale.  Which is currently carbonating and I will reevaluate shortly.

I have been a big fan of all the exBEERiments taking place over on brulosophy.com but I my be letting all their statistically insignificant data carry over into some actually significant brewing processes - I have neglected some cleaning/sanitizing and have been using unhealthy yeast.

Brown Ale Infection

For the brown ale, I have narrowed down the cause of the infection to three potential areas
  1. Unboiled DME
  2. Ball valve
  3. Contaminated yeast
I think my infection came from 1 or 3, while its possible number 2 was the cause, I think its slim. 

1) A little back story - when I kegged my brown ale I cleaned and sanitized my quick disconnect and silicone tubing and I sprayed starsan in and around the quick disconnect on the pot's ball valve. I then attached the hose and gravity drained right from the kettle into a cleaned and sanitized keg.  I grabbed a plastic cup in the brew area and weighed out the DME to use in the keg for carbonation.  I dumped it right in the keg (didn't boil it) and let it sit for a little over 3 weeks to naturally carbonate.

When I hooked up the keg and pull some off, it was all foam and had a very sour note.  I did my research and new I was overcarbonated and it was most likely caused from an infection.  I off-gassed the keg twice a day for over a week until it finally was not pouring foam.  The samples were getting less sour, but they were taking on new off flavors - phenolic, clove, spicey, and a slight "meaty" note all accompanied with an astringent bitterness.  The sourness had faded but this beer was not getting better.

Just like a baseball skipper, I made the call to pull my pitcher and dump the brown ale...

[moment of silence for dumping 5 gallons of alcohol]

Life is too short to drink bad beer!

2) Anyways, I did save a bit of the sample to test and the gravity had dropped 2 points from 1.011 to 1.009 so something unintended definitely got to work in that beer. As you can see from the pictures below, even though I clean out my ball valve and boil kettle after each brew, some stuff gets in those threads.  I have since disassembled and cleaned all of those parts.  I also don't think I am going to be fermenting in the kettle anymore - probably not the cause of the potential grime, but I prefer to see what is going on in the clear better bottles anyways.

You can see the dirt in the 7 to 8 oclock quadrant of the valve

Same picture with slightly different lighting

Flecks of crud on a napkin after brush out the inside of the ball valve


3) The last possible cause for my infection could have been the yeast.  I harvested the WLP002 from inTROduction ale by just pouring the yeast slurry from the better bottle into a mason jar which had been boiled.  It should have been fine, but who knows what was kicking around in the air from the time I finished racking to the keg, until dumping the yeast slurry.  It also took a good 2 days for that yeast to show signs of fermentation.  Definitely plan on making a vitality starter next time.

Off Flavor in Blonde Ale?

So I just kegged my blonde ale on Saturday and taking a swig from my final gravity sample I found myself shaking my head in shame again.  I tasted a little bit of a vegetal character, much like V8 tomato juice.  This is where I am really interested to see how this beer turns out after carbonation - did I get DMS from the 30 min boil?  Or was it the slow start to my fermentation?  A statistically insignificant exBEERiment would state it wasn't the boil time, but instaed was caused by the slow fermentation.

Yeah, you caught that did you?  I had an even slower start to my fermentation in the blonde ale than I did with the brown!  I used WLP090 San Diego super yeast which was a few weeks past its best by date.  I was TOO LAZY to make a starter, so I just took 2 L of my blonde ale wort and added the yeast to the stir plate.  About 8 hours later I pitched the yeast and wort into the rest of the wort to ferment.  It took right under 72 hours for it to start to fermenting - not optimal

Recap

I have been to lazy to make sure my yeast is at optimum health and pitch rate to ferment my beer to its best potential.  I need refocus my efforts toward better brewday preparation.  I will update when i have a better idea about how the blonde turns out.  If it is DMS I am going to have a constant inner battle with whether it was the 30 minute boil, or the slow fermentation start.

I can control both of those variable in my next brew.

Until then...everyone hug your uncontaminated and off-flavor-free beers for me.  You don't know how much you should appreciate them :)



7 comments:

  1. Happens to all of us sometimes. Last year I discovered unfriendlies in one of my kegs, apparently my cleaning of that one keg was not up to snuff and I lost 5 gallons of my house ale. The important part, and you already know this because you're doing it, is to determine where the problem was/is and correct it.
    -Slainte

    ReplyDelete
    Replies
    1. Thanks for the empathy! There are some many nooks and crannies for bugs to get in our equipment. I guess it was bound to happen eventual.

      Cheers!

      Delete
  2. Let's not get too lax; the first true infection is a stark reminder of the ongoing challenges we face. Staying vigilant and following safety protocols is crucial. This serves as a wake-up call to prioritize health measures and adhere to guidelines. In times like these, a collective effort ensures our safety.

    ReplyDelete
  3. Brewing is an art that transforms simple ingredients into a symphony of flavors. The alchemy of grains, hops, and yeast creates a beverage that transcends mere refreshment. Each brew tells a unique story, with skilled brewers as storytellers. From the hoppy embrace of an IPA to the smooth richness of a stout, brewing is a celebration of diversity. It brings people together, fostering community and camaraderie. With every sip, we savor the craftsmanship, passion, and innovation that make each brew a delightful experience. Here's to the endless possibilities bubbling in every batch—a testament to the magic of brewing! Cheers!

    ReplyDelete
  4. This comment has been removed by the author.

    ReplyDelete
  5. Hey everyone, I stumbled upon an insightful resource related to our recent discussion on infections. If you're interested in delving deeper into clinical trials. It offers a visual journey into the world of clinical trials images, shedding light on their importance and impact. In the thread discussing infections, there's a wealth of knowledge shared by our community. Let's expand our understanding by exploring the intricacies of clinical trials together. Feel free to share your thoughts!

    ReplyDelete
  6. In our blog exploring the nuances of craft beer, we delve into the intricate world of brewing, from flavor profiles to potential pitfalls. However, amidst the rich tapestry of brewing tales, a curious incident emerged—**Brown Ale Infection**. This unforeseen microbial intrusion disrupted the delicate balance of flavors, sending shockwaves through the brewery. Amidst the chaos, one brewer found solace in an unlikely ally—their health care thesis. Seeking expertise beyond the fermenter, they **Paid Someone To Write Their Health Care Thesis **, uncovering insights into microbial management and contamination control. This unexpected synergy between brewing and academia not only salvaged the batch but also sparked a new avenue of research in beer microbiology, proving that innovation often arises from unexpected intersections.

    ReplyDelete