Thursday, August 8, 2013

Planning my Indoor Electric Brewspace

Back in March of 2012, I discussed brewstands and recirculation mash system as 'wants' in part 3 of my all grain series.  They are still on my wants list, but with the new house I have decided I need to enact a plan to get indoors for brewing, with electricity.  Too many days where my hands are freezing from cleaning my mash tun out in the cold.  Additionally, we do not have a garage so I would be out in the full elements for brewing.  Below I will go over the pro's and con's of having a dedicated indoor brew setup and then layout my 3 phase plan to get indoors and use induction!

(New house - want to brew INside it, not OUTside it)

PRO's of Dedicated Indoor Brewing

  • Weather - Indoors you can be the postman of brewing - rain, sleet, snow, extreme heat, extreme cold - it doesn't matter.  This is the best reason for indoor brewing and could possibly outweigh any of the cons in and of itself.
  • Dedicated Brew Area - this isn't necessarily only specific to indoor brewing, as having a brewstand on casters would classify.  But having a dedicated space for brewing, you can organize and optimize for an efficient and quicker brew day.
  • Operating Cost - Brewing with electricity is far cheaper and more efficient than propane.  Also, as long as you pay your electric bill you will not run out of fuel - unless there is a power outage.
  • Proximity - Depending on where you setup your indoor brewing you should be close to hot water, and a sink/cleaning area, maybe even a T.V. or bathroom!

CON's of Dedicated Indoor Brewing

  • Initial Setup Cost - To do 5 gallons or more you will need access to 240v electricity with GFI, Ventilation etc.  Also if you want more advanced mash system you will need to spend quite a bit in the electronics department for a control panel.  This is probably the biggest hindrance to going indoor.  People can spend thousands of dollars getting a dedicated brew room - check out to see what i mean.
  • Ventilation - Boiling off 1+ gallons of liquid will create quite a humid environment.  You will need to have some sort of ventiliation to keep the area in and around your brewery dry and free of mold.  Additionally, some family members may not appreciate what I think are wonderful smells of wort and hops.
  • Mobility/Portability - You are kinda stuck to a location with the appropriate power you need.  It will be hard to take your system to club brewing event which is outdoors.
  • Electric knowledge - If you don't already know, you will need to learn a little bit about wiring electricity and electronics OR pay big dollars  to buy a prefabbed setup (see con # 1)

Shegogue Brew's Indoor Electric Plan

  • Frugal - Anyone who knows me knows I love a good deal.  I will DIY whenever I can to save some $$$.
  • 1) Electricity First - The first part of the equation is getting adequate power supplied to the unfinished side of the basement.  This needs to happen anyways to be able to run my keg fridge and ferm chamber - there currently are no power outlets on this side of the basement.  While at it, I will have the electrician wire up power for the brewspace
  • 2) Simple Setup - Once electricity is in place I will be going with a 20a/240v 3500watt induciton cooker.  This removes the need of a control panel, PID's etc.  I will brew in the same manner I currently do outside just with induction rather than propane burner.
    • Vent Hood - I will construct some sort of a vent hood and wire up a 6" inline fan to run the exhaust outside - all DIY, all savings
    • Brewstand - will construct a simple 2-tier brewstand to utilize gravity (as I currently do)
    • Gravity fed MLT

  • 3) Automated Mash Temp Control
    • Add a 15a/120v RIMS or "teakettle" type HERMS system.
    • This will require fancy pumps, and a control panel
    • A lot of extra hardware for installing valves into kettles
Step one should be completed sooner than later. Hoping to be able to jump into step 2 after the Xmas season (hint to santa).  And Step 3 will be a year or two out, maybe longer - really need to rebuild our deck.  As long as I am inside, I think I will be a real happy brewer :)


  1. Good luck moving indoors, it's the way forward! Having just done out my kitchen and fitted a new induction hob for ordinary cooking, I would recommend you use a magnet to check your brew pot is compatible.

  2. I just purchased a new brew kettle off of a homebrew site classified. I believe it is magnetic (bayou classic pots usual are) but I will need to confirm before I get the burner. Thanks for looking out!

  3. Any updates? What's the boil capacity of that burner?

    1. Hi Justin - Unfortunately, I do not have any real updates. I did have the electrician in last fall and I am wired for this burner. Looking through posts online I have seen people get up to 10 gallons to boil (takes a while). I only plan on doing 5 gallon batches so I am not worried about power. Crunching some numbers it looks like it will be faster for 5 gallons then my propane setup.

  4. This comment has been removed by a blog administrator.

  5. It would not be fair if we compliment all the blog writings but not the author.
    billig strøm

  6. A problem with copper is people stealing the wiring. People often steal copper wire for money. However, if someone comes into contact with a live copper wire while trying to steal it, he or she can receive serious injuries. Or, even possibly death. It is always best to leave copper wiring where it is, unless there is some sort of safety issue.Bussmann Fuses

  7. He thought that Edison's power network based on low-voltage direct current was too inefficient to be scaled up to a large size. In 1885 Westinghouse purchased power transformers developed by Lucien Gaulard and John Dixon Gibbs. electrical contractors in sewell nj

  8. I am unquestionably making the most of your site. You unquestionably have some extraordinary knowledge and incredible stories.

  9. this is really nice to read..informative post is very good to read..thanks a lot! Electrical Repair

  10. I really appreciate this wonderful post that you have provided for us. I assure this would be beneficial for most of the people.

  11. Awesome is the most appropriate word to portray this blog.
    southend electrician

  12. In this case you will begin it is important, it again produces a web site a strong significant internet site:

  13. Thanks for the tips guys. They were all great. I have been having issues with being fat both mentally and physically. Thanks to you guys i have been showing improvements. Do post more.

  14. if you always use your swimming pools, you will need to use some quality pool cleaner a lot“ obsolete electronic components

  15. That is really nice to hear. thank you for the update and good luck. Auto Electrical Repairs Reading

  16. it was a wonderful chance to visit this kind of site and I am happy to know. thank you so much for giving us a chance to have this opportunity.. best electric mops

  17. Auction sites are almost always a waste of time. They're crowded with other people trying to sell old electronics for money, aren't likely to draw in the kind of customers you want, and you'll almost never get enough bids to meet the price you want.Electronic components online

  18. Matric Class Result of all the BISE boards will be announced in July. The students who are waiting for the10th class result 2020 date should stay with us on The 10th class exams 2020 is conducted by all the educational boards that are across the country.

  19. Thank you because you have been willing to share information with us. we will always appreciate all you have done here because I know you are very concerned with our. best electric tea kettle

  20. This blog has a positive and eager result.
    gu10 led